The Prusa i3 is an open-source fused deposition modeling 3D printer. Part of the RepRap project, it is the most used 3D printer in the world. The Prusa i3 was designed by Josef Pr??a in 2012 with the Prusa i3 MK2 being released in 2016 and the MK2S being released in 2017. The latest version, called the Prusa i3 MK3 was released in September 2017 with significant improvements over the prior models. The Prusa i3's comparable low cost and ease of construction and modification has made it popular in education and with hobbyists and professionals. Due to the printer being open source there have been many variants produced by companies and individuals worldwide, and like many other RepRap printers the Prusa i3 is capable of printing some of its own parts.
Video Prusa i3
History
The Prusa i3 is the third printer design by Josef Pr??a, a core developer of the RepRap project who had previously developed the PCB heated bed. The first iteration was the Prusa Mendel produced in 2010 followed by the Prusa Mendel (iteration 2), in 2011. The printer was named Prusa Mendel by the RepRap community rather than Pr??a himself.
Prusa Mendel
The first Prusa Mendel was released in September 2010 with the aim of simplifying the existing Mendel design, including reducing the time needed to create the 3D printed parts from 20 to 10 hours and 3D printable bushings replacing regular bearings.
Prusa Mendel (iteration 2)
The second Prusa Mendel was released in November 2011 and with upgrades including snap fit parts, reduction of the number of tools needed to construct, maintain the printer and improved belts attached to the stepper motors and use of LM8UU linear bearings.
Prusa i3
In May 2012 designs (produced in OpenSCAD) for the Prusa i3 were released, it was a major redesign from previous versions and other RepRap printers. The design replaced the triangular threaded rod frame construction with a water jet cut aluminum frame, had a food-safe hot end called the Prusa Nozzle, and used M5 threaded screws instead of M8. The design focused on ease of construction and use rather than maximising the number of self replicated components. In 2015 Pr??a released a version which he called the Original Prusa i3, selling through his company Prusa Research.
Prusa i3 MK2
In May 2016 the Prusa i3 MK2 was released, it is the first printer with automatic geometry skew correction for all three axes and includes a larger build volume, custom stepper motors with integrated lead screws, mesh bed levelling using a non-contact inductance sensor and a rewritten version of the Marlin firmware. Other new features include a polyetherimide print surface, Rambo controller board and an E3D V6 Full hotend. The Prusa MK2 became the first RepRap printer to be supported by Windows Plug-and-Play USB ID.
Prusa i3 MK2S
In March 2017, Josef Prusa announced on his blog that the Prusa i3 MK2 was now shipping as the Prusa i3 MK2S. Enhancements cited include U-bolts to hold the LM8UU bearings, improved LM8UU bearings, smoother rods, an improved mount for the inductance sensor, improved cable management, and a new electronics cover. While new shipments of the MK2 will automatically receive the "S" upgrades, an upgrade kit is available to bring these improvements to earlier purchasers.
Prusa i3 MK3 and MK2.5
In September 2017, Prusa i3 MK3 was released, marketed as "bloody smart". Upgraded features are: sturdier Y axis, new extruder with double side grip on filament, quieter fans with rpm reporting, updated bed leveling sensor, new electronics board named "Einsy", quieter stepper with 128 step microstepping drivers and magnetic heatbed with interchangeable PEI-coated steel sheets. There are new sensors: several temperature sensors, a filament detector, and a power panic sensor. The printer now runs on 24V instead of 12V, so all the electrical components were updated to 24V variants. The printer also offers dedicated socket to connect Raspberry Pi Zero W running open source Octoprint software for wireless printing, and offered a custom Octoprint build for Prusa i3.
The idea of MK3 update was to make the printer easier to use for casual users and do less failed prints. The filament detector allows to load filament just by pushing it in, and it could detect and pause the print if the filament is jammed or runs out. Both scenarios allow the print to continue normally after the issue is fixed. The new stepper motor drivers can handle skipped steps automatically and prevent layer shifts. The power panic sensor allows the printer to recover from power outages, and uses the remaining charge in the power supply's capacitors to lift the print head up to prevent it from melting the printed part while the power is out. The ambient temperature sensor is able to detect mainboard overheating caused by loose electrical connections.
The upgraded chassis and electronics also allow for faster print speeds -- up to 200 mm/s.
Existing MK2 and MK2S users were offered a $200 partial upgrade named MK2.5, limited to features which are cheaper to upgrade. After negative feedback from the community, Prusa agreed to offer a more expensive $500 MK2S to MK3 upgrade.
Clones
As an open-source design the success of the Prusa i3 is underlined by the ready availability of both complete and kit-built machines that follow the various iterations of the i3 design. Rather than compete directly with these versions, Prusa Research's strategy is to pursue continual refinement of its designs.
Recognition
In 2012 Josef received honours from the governor of the Vyso?ina Region in the Czech Republic for his accomplishments in technology. In February 2014 he was featured on the cover of Czech Forbes magazine as one of the 30 under 30 list.
Maps Prusa i3
Capabilities
Self replication
Like other RepRap printers the Prusa i3 is capable of creating many of its own parts, which were usually printed in ABS plastic prior to the Mk3, which uses PETG instead. The standard Prusa i3 has 26 printed parts.
Printable materials
Depending on the hot end and heated bed installed, the Prusa i3 is capable of printing many materials including Acrylonitrile butadiene styrene (ABS), polylactic acid (PLA), high impact polystyrene (HIPS), polyetilene (PET), different flexible filaments (FLEX), polypropylene (PP) and nylon. Different materials require different working temperatures and techniques to make them adhere to print bed well
Components
The Prusa i3, like many RepRap printers, is made from a combination of self-replicated 3D printed parts and off-the-shelf components which are commonly referred to as "vitamins", as they cannot be produced by the printer itself.
The vitamins used on the Prusa i3 are a combination of common components including threaded rods, smooth rods, screws, nuts, 5 NEMA 17 stepper motors and more specialist equipment including a controller board, heated bed and hot end.
Variants
Due to its popularity the Prusa i3 has many variants produced by different companies and individuals around the world including different styles of frame and extruders.
Frames
The main variant in designs of the Prusa i3 are different frames used, these include a single sheet frame cut from steel, acrylic (laser cut or CNC milled), medium-density fibreboard box frames and Lego.
Extruders
There are a range of different extruders used on variants of the Prusa i3 including 1.75 mm and 3 mm filament extruders and other tool heads including a MIG welder and a laser cutter.
References
External links
Websites
- Prusa i3 MK2 page on Reprap.org
- Prusa i3 page on Reprap.org
- Prusa Research
Open source files
- Prusa i3 MK2, Prusa Research repo on Github
- Prusa i3, Prusa Research repo on Github
- Prusa Mendel iteration 2, Josef Prusa repo on Github
Videos
- Josef Prusa YouTube channel
- Review of the Prusa i3 MK2 by Thomas Sanladerer on YouTube
- Josef Prusa interview about the Prusa i3 Mk2 multiextrusion upgrade kit
- Open-Source, New Factory and the End Goal: A Chat with Josef Prusa of Prusa Research, All3DP
Source of the article : Wikipedia
0 Comments